Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
They are making several great pointers related to How to Install a Bathtub Yourself overall in this great article following next.
Installing a bath tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough job. If the old tub is easily obtainable, the project can relocate quickly; if you need to open up a wall to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly assist you mount a new bath tub in your shower room if you have actually currently acquired a brand-new tub as well as don't need to transform the arrangement of your previous water supply pipes.
Your devices and material list should consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic because of the limited access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and the sink. Secure the faucet in position with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The former type should be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using both wood boards under its feet, place the bath tub in the required position. The wooden boards are helpful in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the bathtub till the level reviews level.
To set up taps, fit all-time low of the furthest versatile faucet port to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as additionally check the overflow outlet and the typical outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait till the bath tub has actually been made use of a minimum of when as this will certainly resolve it right into its last placement.
Preparing for the Setup
First of all, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final placement.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can crack rather very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very focused on Tools You Need to Install a New Bathtub and I hope you enjoyed reading the entry. Please take the time to share this article if you liked it. Thank you so much for going through it.
Quick fix? We're here. Report this page